Nueva versión disponible de AirOS v5.5.2 (17-08-12)

Publicado por D3M0N, 17 de Agosto de 2012, 07:52:59 PM

Tema anterior - Siguiente tema

0 Miembros y 1 Visitante están viendo este tema.

D3M0N

Desde la Ubiquiti World Conference en Buenos Aires, Argentina. Les taigo la nueva versión presentada del AirOS para equipamientos Ubiquiti con soporte AirMAX.


Soporte para:
  * Bullet M, Titanium
  * Rocket M, Titanium
  * NanoStation M
  * AirGrid M / AirGrid HP M
  * NanoBridge M
  * PowerBridge M
  * PicoStation M
  * NanoStation Loco M
  * AirRouter
  * PowerAP N
  * Rocket M365
  * Rocket M900
  * NanoStation M365
  * NanoStation Loco M900
  * NanoStation M900
  * NanoBridge M365
  * NanoBridge M900
  * NanoBridge M3
  * PowerBridge M10
  * NanoStation M6

Datos adicionales:
Version 5.5.2-Service Release (August 17, 2012)
----------------------------------------------
New product support:
- New: Rocket M2 Titanium
- New: Rocket M5 Titanium
- New: NanoStation M6

Regional Updates:
- New: Enable DFS frequencies for US/Puerto Rico/ Canada for NanoStationM5/Loco M5/Rocket M5/Rocket M5 GPS/NanoBridge M5 models
- New: Lock Indonesia country code: once selected at Login page do not allow to change country unless reset to defaults 
- New: Remove DFS enable/disable option for Austria, turn DFS ON after upgrade for Austria. Keep DFS enable/disable option for rest of EU countries
- Fix: Regulatory rules update for India 2.4GHz band
- Fix: Move Puerto Rico under US regulatory domain

Fixes:
- Fix: AirMax: When one of the clients reboot all others are disconnected from AP
- Fix: AirMax: Unexpected device reboots on high load/PTMP (possible fix) 
- Fix: Traffic shaping ingress rules on LAN port in some cases block Internet traffic
- Fix: Traffic shaping bursting is increased to the maximum allowed value according to configured throughput limits
- Fix: Association to non-broadcasting SSID CISCO AP takes couple minutes
- Fix: Complex AP-repeater setup creates loop in this network
- Fix: Increase Password attribute length to 18 when sending empty password to RADIUS server
- Fix: Auto Channel selection logic improvement
- Fix: DFS: Allow UNII-2 band for Canada w/o unlock key for approved product models
- Fix: Traffic Shaper rules changes during upgrade from v5.3.5
- Fix: PPPoE stops sending PPPoE Discovery packets on time change
- Fix: NBM3/NBM365 should support 2 Ethernet ports but shows only 1.
- Fix: Aggregated transmission problems with some Apple laptops and other devices
- Fix: Clients can't reconnect to AP with WPA2-AES security reason (15)
- Fix: After upgrade from v5.3.5 to v5.5 secondary Ethernet port isn't configured (running default configuration)
- Fix: Stations disassociation because of returned broadcast packets on Ethernet interface
- Fix: Second LAN port MTU max is 2024B not 1614B (affected all M series products)
- Fix: No Internet connection for clients behind device in router mode
- Fix: Access Point ignores Session-Timeout limit received from RADIUS server
- Fix: Reduce false positives and misclassifications of invalid DFS radar events
- Fix: Can't launch Airview when initial window disabled
- Fix: Making changes in Network tab resets MTU to 1500 when Management VLAN is enabled
- Fix: Incorrect ebtables VLAN drop rules
- Fix: Do not allow to upload Configuration file from different Regulatory domain 
- Fix: Port Forwarding public port range issue

- WEB UI: Show DFS status in MAIN page
- WEB UI: airSync: Show correct default slots depending on channel size
- WEB UI: Static route disappears in Router mode
- WEB UI: Option to disable Multicast Enhancement for AP
- WEB UI: Improved IP address validation
- WEB UI: Don't enable "DMZ Management Ports" when DMZ is enabled (Router/SOHO Router)
- WEB UI: Bridge table display problem. Table too big
- WEB UI: Do not show graph for interface when it is not in use
- WEB UI: Don't report TOUGHSwitch/airCam WLAN mode in device discovery results
- WEB UI: Add Turkish language support
- WEB UI: In Simple configuration mode LAN should be BRIDGE0 containing both Ethernet interfaces
- WEB UI: Show the same antenna information in MAIN page as in Wireless settings page drop down
- WEB UI: Site Survey Scan button is disabled under IE browser
- WEB UI: Allow MAC Cloning for BRIDGE interface in Router mode
- WEB UI: Bridge table is not displayed in Main page when there are multiple bridge


Security Improvements:
- WEB UI: Default settings change: Enable HTTPS (port 443) by default
- WEB UI: Removed admin.cgi functionality
- WEB UI: Add option to disable HTTP service
- WEB UI: Add reminder when using default admin user name/ password


Pueden descargarlo directamente desde el sitio web oficial de Ubiquiti:

You are not allowed to view links. Register or Login

DESCARGA: You are not allowed to view links. Register or Login

wh00t

hola D3M0N

Podrías hacer por favor un mini tutorial o basico entendible de como descompilar o descomprimir o montar un firmware bin de ubnt para hacer algunas pruebas?
hace unos dias atras probe no me salio me faltaba algunos pasos asique no llegue a nada
quisiera poder lograrlo para poder hacer algunas pruebas y ver algunos archivos


Saludos
muy bueno los ultimos post

D3M0N

Bueno, en este caso actualizaremos el AirOS de nuestro equipo Ubiquiti Nanostation M2, vamos a ir a la pestaña "System" y hacemos click en "Update..." por defecto, los Nanostation M2 suelen venir con el AirOS 3.5:


Se nos abrira una ventana en la cual vamos a seleccionar el Fichero que descargamos del sitio de Ubiquiti. AQUI.

y le daremos click en "Subir"...


Una ves subido confirmaremos haciendo click en "Update"


Tardara unos minutitos y se completara la actualización; recordar no apagar, ni desenchufar en nanostation ya que no se podra volver a recuperar..


una ves terminado se cerrara la ventana y nos vamos a loguear nuevamente..


y ya tenemos nuestro Nanostation M2 actualizado a la ultima versión del AirOS.